26 Oct 2022

Navigating Hazardous Area Safety Requirements

Where safety and compliance in hazardous environments are concerned, there are a lot of acronyms relating to standards, directives, regulations etc. To those unfamiliar with how the whole legislative landscape operates, it can easily and quickly become confusing. To help Renew's readers tackle the minefield, safety compliance expert and AEMT lecturer, Peter Rawlinson, looks at the key requirements you may come across concerning hazardous environments, what they cover and how they relate to each other.

Before we get into specifics, it might be helpful to outline how different types of requirements compare. A Standard is a technical specification covering aspects such as dimensions, capacity, ratings etc. It is not a legal requirement but is widely considered best practice.

A Regulation in EU terms is a piece of law universally applicable to all EU member states.

An EU Directive is a legislative act outlining objectives that all EU member states must translate into their national legislation.

A Statutory Instrument is similar to an EU Directive and is the principal form in which delegated legislation is made in Great Britain.

Certification is the process of certifying that products, processes and people pass performance and quality assurance tests outlined in relevant standards and legislation.

 

IECEX

The first acronym we will look at is IECEx, (International Electrotechnical Commission System for Certification to Standards Relating to Equipment for Use in Explosive Atmospheres). This aims to 'facilitate international trade in equipment and services for use in explosive atmospheres, while maintaining the required level of safety'. The IECEx system started as a product certification scheme but has since expanded to cover personnel certification offering competence training for people working in explosive atmospheres.

IECEx has a broad global reach and is sometimes referred to as a passport scheme in so far as it is accepted by many countries prima facia, while some may accept it but require signing up to a local scheme. Indeed, the IEC scheme is the starting point for the development of the standards for EX equipment, and use.

Because of its international scope, the Ex Repair training offered by the Association of Electrical and Mechanical Trades (AEMT) follows unit Ex 005 of the IECEx Recognized Training Provider Programme (RTPP), which focuses on the BS EN IEC 60079-19 standard on repair, overhaul and reclamation of Ex equipment, alongside the BS EN IEC 60034-23 standard "Rotating electrical machines - Part 23: Repair, overhaul and reclamation".

 

ATEX

 The ATEX directives are two EU directives describing the minimum safety requirements for workplaces and equipment used in explosive atmospheres, which must be applied in law by EU member states. There are, in fact, two directives. The ATEX' equipment' Directive 2014/34/EU covers equipment and protective systems being used in potentially explosive areas. The ATEX 'workplace' Directive 1999/92/EC covers the minimum health and safety measures that need to be in place to protect people working in hazardous areas.

 

UKEX AND DSEAR

 UKEX is a UK Statutory Instrument. This is a direct transposition of the ATEX equipment directive into UK law under the new post-Brexit regime. This is driven in the UK by the UKEX AB (Authorised Body) group. The members of this group are also ATEX and IECEx certification bodies. It is in their interest for there to be ongoing alignment between the directives, and so it is unlikely that there will be a divergence between UKEX and ATEX despite the pending Brexit Bill and its impact on UK legislation.

DSEAR is also a UK Statutory Instrument and is a direct transposition of the ATEX workplace Directive into UK law. However, it also covers the requirements of the Chemical Agents Directive.

So, in essence, as far as regulation of hazardous area equipment and environments is concerned, IECEx is the starting point that enables the ease of gaining ATEX and now UKEX. As such, if IECEx is amended, the amendments will automatically be adopted by the ATEX Directive and UKEX regulations by means of the acceptance of such amendments being "state of the art" for explosion protection.

 

CSA, UL AND FM

 Finally, you may come across CSA, UL or FM certifications. This is a broad system to ensure the safety of products used in North America, including Canada, whereby an OHSA or SCC-accredited Nationally Recognized Test Lab (NRTL) can certify that a product complies with specific North American safety standards. There are several standards which apply to hazardous areas under the North American system; for example, FM 3615, UL 1203 and CSA C22.2 No. 30 are the standards for Explosion-Proof Equipment, while UL 674 and CSA C22.2 No. 145 cover "Electric Motors and Generators for Use in Hazardous (Classified) Locations". Some N American explosion protection standards are harmonised with the IEC, ATEX and UKEX systems, and others are not. In addition, the N American system follows a different environment classification system.